How to Remove Shower Drain Flange: 7 Easy Steps

There is a proverb that says a hygiene toilet and a clean kitchen can hold your personality. We are always determined about our kitchen, but some of us may not be conscious about our toilet. 

Sometimes the drain of your toilet is worn out or previously damaged. And you might see signs of mold or mildew growth, or your shower doesn’t drain as well anymore. 

If it happens in your bathroom, there must be a way for you to fix it yourself without hiring a plumber. 

Unfortunately, the only way to fix a leaky shower drain is to remove and replace the flange.

A shower drain flange is designed to help direct water flow in your shower. But sometimes the rubber covering the drain is old. 

However, by following our easy steps on how to remove shower drain flange, you can do it by yourself very easily. 

But before following the steps, you should know about the tools that are needed to do this job. 

In this post, we also mention what you should do with your flange and what not. So keep reading!

Why Should You Remove The Shower Drain Flange?

There are three reasons how to disconnect a shower drain flange. The most common reason is that the flange needs to be replaced. It is a very common problem, so your flange may need to be replaced.

The second reason for removing the shower drain flange is that they are doing something like putting in a new tub or surround. 

Whether it is tiling or some other improvement, you will have to remove the old tile, drain, and surround before you can replace it with something new!

One last reason is that something down there has been corrupted or broken. You may need to remove the drain from your shower because the drainpipe is starting to leak. 

If this happens, you will surely remove the flange to deal with whatever pipe problems. 

Before getting started read our Instructions for removal of the shower drain flange.

Instruction For Removal Of The Shower Drain  Flange

To cut out a shower drain, the drain assembly can be accessed through the shower floor. 

Plucking out by separate pieces through instructions by which anyone can remove their different types of a shower drain.

The Tools You Need and Uses

The following tools are needed if you would like to remove your shower drain flange with a tool. You can know the uses of these tools at the same time. 

According to your flange, tools can be different like Fiberglass shower drain Removal Tool, Plastic Shower Drain Removal tool, and others. We are talking about it in general.

1) Pliers/Crescent Wrenches:

You can use pliers or crescent wrenches (Allen wrench) when removing the old flange. Be careful not to damage any connections while removing the old unit that might be connected to it.

2) Putty Knife:

If the flange is made of copper, you can use a putty knife to scrape away the old material. Be careful not to scratch any nearby materials or surfaces.

3) Rag:

This is used to wipe up messes and keep your hands clean as you work. Ensure it is durable enough not to rip when using it on a dirty surface or pipe.

4) Utility Knife:

Use this tool to remove any caulking still left around the pipe. Make sure it has a sharp blade so that it can easily cut through the old caulk. The sharp blade can cut without causing too much damage or scratching the metal surface.

5) Bucket:

You will need to use this to submerge the flange in water. You can use an empty bathtub to cover the flange until it softens up.

6) Safety Goggles:

Ensure that you wear these when handling caulk remover, as well as any other chemicals used on your drain.

7) Gloves:

These should be worn while you work on your drains. Because they will protect your hands from any corrosive material when removing the old materials. 

How To Remove Shower Drain Flange?

how to remove shower drain flange

When it comes to remove your flange, you should know how to remove old shower drain flange. The hardest portion is to remove the old shower drain flange. In the meantime, you can remove your flange using a tool, or using no tool. We suggest using the tool because it is safe and good.

Using Tool

Here are some steps to give you the full guideline to remove your shower drain flange properly. 

Step: 1 – Set Location

Locate how high up on the pipe the flange is situated. Use a level to check to apply the compound directly under it.

Step: 2 – Use Safety Wear

Put on safety goggles and wear rubber gloves. Squirt some tub and tile caulk remover into an old bucket or tub of water, depending on what is available. You will have to submerge the flange in one of these containers to soften the sealant located around it. 

Step: 3 – Remove Concrete Around The Drain

Take a putty knife or any flat object that is not sharp and scrape off any caulking surrounding the flange. Once you have scraped all of it off, take a razor blade and cut away any caulking that is left behind, as well as any leftover residue from around the flange itself.

Step: 4 – Cleaning

Take a steel pipe brush and clean the drain hole around the flange. Then Scrub away any leftover residue to ensure that the floor is absolutely clean.

Step: 5 – Remove Drain Cover

Remove any loose caulk left around the flange with a putty knife, rag, or razor blade. 

Step: 6 – Screwing

Fill in the opening where the old flange used to sit with new caulking. Make sure you apply enough pressure while screwing on your new flange to create a tight seal.

Step: 7- Observing Leakage

Let everything sit for eight hours or overnight before you start seeing if your shower drains properly again. 

Run some hot water over it and make sure there are no leaks anywhere before enjoying your newly fixed shower drain flange.

Always remember to inspect your drain flange before you start any repair. This period can help prevent it from leaking. 

Still, if it has shown signs of being damaged in the past and has been repaired, there is a chance that this process won’t be enough to repair it completely.

 Without Using Tools

How to remove shower drain without a tool? If there are no tools, anyone can easily remove the shower drain. 

  1.  Smoothly twist anticlockwise to remove.
  2. When you get any small screw, spin a flathead till unsecured it to remove the stopper. 

How To Remove Shower Drain Cover That Is  Grouted In

  • Fresh the roof off and remove extra when the cover is removed. 
  • Secure the drain cover off the shower and place the vacuum hose right up counter to the drain. 
  • Hoop a piece of string through the drain holes in the grate.
  • Rather use a metal coat hanger or other strong stuff to hoop around the holes in the drain cover. 
  • Then drag the hook end of a hammer to lose the cover. 

Replacing Shower Drain In Concrete Floor

When you have an old blockage shower drain, it would be best Replacing shower drain in concrete floor. 

Besides all you need are some essential tools and defense material, and you can fairly replace a shower drain on the concrete floor. 

  • To uncover the flange, use a hammer and knife or any shaping tool to split the concrete. You can do it until you uncover the drain flange and pipe holding the drain section. 
  • Unlock the bolts gripping the pipe rough-in and the drain within the concrete floor. To loosen the screws, apply a proper sized wrench. 
  • Apply a screwdriver to support you and pressure drain the flange until you bust the bond with the pipe cement. Point the old bolt holes from the flange to handle leverage. Remove your aged drain from the pile. 
  • Fresh the pipe stack with an old rag. You can give the primer to the inward pipe drift approaching through the concrete slab and the outside of the shower drain. When the primer dried, use pipe cement to the new areas. 
  • Lose the bolts on the flange and fix the shower drain cover in position, limply it over the high of the bolts, and turn it until it is in place. 
  • Apply a spray bottle with water to easily mist the hole’s border. You will be stuffed with concrete to get clear of dust and support new concrete more expertly to the old concrete. 
  • Fill all over the drain area, covering the bolts and the flange. After that apply a plain metal shovel to fluid the new concrete flush to the rest of the floor. Then cut out the tape when the concrete has time to dry.

You Should Do And Don’t

If you’re like the rest of us, you’ve lived with your shower drain flange for years and never even thought of replacing it. 

But if you do not know how to remove sink flange, new sink doesn’t seem to be draining properly. It might be time to get a recommendation and get that old thing taken care of.

What You Should Do:

  • Locate the current shower drain flange. It can typically be found near the outside edge of the bathtub. Or on a wall near where the tub meets the floor. Because that’s where water typically pools during showers or baths. As a result, if you don’t see one, it might be near the wall or floor behind the tub.
  • Determine whether or not it’s stuck to the wall or just installed there. If it is screwed into a hole in the wall, many times, all that’s needed to remove is a screwdriver to get it out of there. Suppose, it’s poured cement and silicone (which is an easy fix). In that case, you’ll need to work a strong solvent like acetone around the edge of it. Then you have to wait a few minutes before removing it with pliers.
  • Install your new flange by applying caulking around the outside of its bases, like installing tile in your kitchen or bathroom. The caulking will act as cement as well as a waterproof membrane. Finish it off by securing the flange to the wall with screws.

Here Are Some Things Not To Do:

  • Don’t try to remove it by prying it up with a screwdriver. It will usually crack the old one and make your job needlessly harder. Moreover, it can also leave you with a hole in your tub or wall from where you prayed against it. 
  • Don’t use wood screws to mount the new one if possible, since wood eventually warps and needs replacement again. However, screws are stronger and don’t require replacement.
  • Don’t try to remove the old shower drain flange using acetone. Use acetone as a last resort when silicone doesn’t work.
  • Never use a line wrench to remove it from the wall since you can damage the flange and make your job more difficult. Use pliers or even a small screwdriver instead.
  • Don’t cut through the old one with a utility knife unless you’re intent on tearing a new one out of your tub. You need to either pry out or cut through plugs rather than cutting against the edges of tubes. It allows the sink or tub to replace without any cutting or repairs.
  • Don’t leave the old one in place if you’re going to be working on a new one. It’ll just leak for sure, and that’s not good!

The purpose of this post is to provide helpful information for DIYers needing to remove the flange from their shower drain.

Caution:

Review this information before you start to remove the old flange, if possible. These instructions are general. 

It can change depending on the roof type you have under your roof. Also, it may be a good idea to call a professional when trying to repair your toilet. 

They can advise you on what repairs are possible and how to proceed with them.

 Frequently Asked Questions

 1. What Is The Easiest Way To Remove A Shower Drain?

 Ans: Hold both of your pilers forcibly and lift the shower drain outside the hole. Lift the drain leisurely (slowly) to escape the denting or any other way damaging the drain. 

 2. How Do You Remove A Stuck Bathtub Flange?

 Ans: You can attempt using a filter jerk (wrench). It is an immense device when the inside helps are still in position. It lets the wrench object hold on to during the time disconnect the flange.

 3. How Do You Remove A Shower Drain Insert?

Ans: Grab the lid body in positions and disconnect the highest (top) knob (counterclockwise) with pliers and a soft grippy to head off (prevent) scratching. 

4. How Do You Remove A Shower Drain Insert?

Ans: Composite together 1 cup of baking soda and 1 cup of vinegar. You should discharge sizzling water, drain the drain to loosen first, use the baking soda vinegar mixture, and pause for 15 minutes. Wash out with more boiling water. 

5. Why Can’t I Detach My Shower Drain?

Ans: You can slow down spin the knob anticlockwise, looking up a screw set on the knob. In case there isn’t one, spin the stopper anticlockwise.

Final Words

The process of removing a flange depends on how difficult or easy it will be for you. 

For this purpose, you may choose to replace your entire shower surround with tiles instead of pulling out the old flange. 

Your first step towards how to remove shower drain flange is making sure that you have all of the tools necessary for the job.

Surely, you are wearing protective clothing like gloves and goggles to avoid getting injured during the process.

If you are doing any remodel, you will want to ensure that the drain flange is removed. Otherwise, it may get in the way of your project. Hope you like it.

Leave a Comment